11/23/2023 0 Comments Raspberry pi cgminer asic![]() It is well suited to the latter task, since controlling ASIC miners requires very little in the way of CPU performance just the ability to run a minimal operating system with network access, and some simple software to fetch work from the network and feed it to the ASICs. However, most people use it in a very different way: not to do the mining itself, but as a controller for ASIC mining devices (typically for Bitcoin and other SHA256 coins, not scrypt). The asker probably got this idea because there is lots of discussion on the Internet about using the Raspberry Pi for mining. It appears that current versions of cgminer have removed scrypt support altogether.Īs Hồ Tuấn Kiệt points out, a Raspberry Pi would be hopelessly underpowered for CPU mining of any kind, so this would be a really ineffective idea even if it worked. The asker evidently did not enable it, which is why it does not work. The higher the hashrate, the bigger is the deviation from this average, caused by ASIC manufacturing tolerances.Might as well give this old question an answer.Ĭgminer 3.7.2 (which was obsolete even when this question was asked) required scrypt to be enabled as a compile-time option with.If you want to operate your Miner without active cooling, we recommend a Clock Rate up to 100 MHz max. The Clock Rate can be set with the following commandline parameter: gekko-newpac-freq. The example above shows a Solo-Mining configuration in Con Kolivas’ Solo Mining pool. Please contact your pool operator or check the pool setup guide for more details. The Pool configuration which is used in the example above should be replaced by your own pool configuration data. cgminer -o stratum+tcp://:3333 -u 1BURGERAXHH6Yi6LRybRJK7ybEm5m5HwTr -p x -suggest-diff 32 -gekko-newpac-freq 150 The following command will start up the CGMiner Software (example): cd ~/mining/newpac/cgminer We achieved best results with dem Arctic Breeze Mobile 92 mm (quiet, performant, high-quality). We recommend a quality USB fan for operating clock rates greater than 150 MHz. For more details please check the following link on : here Users reported several compatibility issues with USB 3.0 Hubs with Intel chipsets. We highly recommend the GekkoScience 7-Port USB Hub which was specifically designed for the operation with USB stick miners. This USB Stick Miner requires a actively powered USB Hub which can independently provide 2 A for each USB port We have achieved good results with several USB 2.0 Hubs from Anker or Orico. This command returns a list of detected miners. autogen.sh -enable-gekkoĮxplanation notes: The build parameter –enable-gekko activates the GekkoScience drivers both for Compac (single ASIC) and 2Pac (dual ASIC). The build command for Ubuntu 16.04.1 LTS (or higher) is slightly different: CFLAGS="-O2 -march=native". Now you can clone the GekkoScience CGMiner branch from GIT: mkdir -p mining/newpac cd mining/newpacĪfter successful cloning you can start to build CGMiner: CFLAGS="-O2". Sudo apt-get install -y build-essential git autoconf automake libtool pkg-config libcurl4-openssl-dev libudev-dev libusb-1.0-0-dev libncurses5-dev libncurses5-dev: text based user interface for CGMiner.libusb-1.0-0-dev: USB support for CGMiner.libcurl4-openssl-dev: http connectivity for CGMiner.libtool: provides shared library access for CGMiner.build-essential: Compiler and Compile-Werkzeuge.The following packages are mandatory to properly build CGMiner: ![]() It’s not necessary to use root.įirst steps: update and upgrade of system and reqired packages: sudo apt-get update ![]() This installation guide describes setup, configuration and build based on a freshly installed Raspbian (Debian) or Ubuntu installation. Preparation, Package Dependencies, Configuration and Build for Raspbian – Kernel version: 4.4 (Debian 8.7.1) or higher of for Ubuntu 16.04.1 LTS or higher Preparation ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |